The machine may encounter problems during operation. Causes can include hardware connections, software errors, network issues, user settings, material properties, or environmental factors.
You can view these codes:
Please use the module code above to locate your specific error code. Based on those error codes, you can find the likely cause and recommended action in the content below.
Homing failed, photograph task not completed, please troubleshoot!
Tool head cannot move, photograph task not completed, please troubleshoot!
Fill light failed to turn on, photograph not completed, please troubleshoot!
Photograph timed out
Photograph failed, camera not found
Machine is not idle, this command cannot be executed
Please close the top cover
Please close the front cover
Device is already photographing, please do not initiate again
Core controller not connected, unable to execute photograph
Core controller not connected, unable to execute photograph
Job completed
Invalid parameters
Machine is not idle, this command cannot be executed
File transfer service timed out
File transfer MD5 check failed
Machine is not idle, this command cannot be executed
Please close the top cover
Core controller not connected
Tool head not connected
Tool head temperature too high, unable to operate. Please try again later!
Job file version not supported, please upgrade software or firmware!
Job file parsing failed, please confirm software version matches firmware!
Job file invalid
Invalid job file
Job file parsing failed
Unable to execute Z-axis homing
Z-axis homing failed
Z-axis homing timed out
Unable to execute X-axis homing
X-axis homing failed
X-axis homing timed out
Unable to execute Y-axis homing
Y-axis homing failed
Y-axis homing timed out
Job file invalid
Job file invalid
Measuring failed, core controller offline
Measuring failed, tool head unable to move
Measuring failed, job terminated
Measuring failed, job terminated
Measuring timed out, job terminated
Measuring failed, Z-axis unable to home, job terminated
Running: start positioning failed
Job failed, core controller offline
Running: notify start failed
Running: G-code batch send failed
Running: notify end failed
Running: wait for printer finish timed out
Pause job: invalid state
Resume job: invalid state
Stop job: invalid state
Temperature out of range: job paused
Emergency stop triggered
Job out of bounds, job terminated
G-code error, job stopped
Core controller error, job terminated
Target measuring position out of bounds, job terminated
Measuring command execution error
Core controller error during measuring, job terminated
Cooling fan disconnected, job paused
Cooling fan not installed
Tool head lost connection, job terminated
Homing failed, job terminated
Printer slave not ready: job aborted
Motor driver fault: job aborted
Front lid open
Framing failed, core controller offline
Framing error, framing file not found
Machine is not idle, this command cannot be executed
Device is running, unable to respond to this command
Framing timed out
Homing failed, framing not completed
Invalid framing file
Framing failed, tool head not connected
Framing out of bounds, please adjust the starting position
G-code exception, framing failed
Framing failed, core controller error
Framing failed
Framing actuator unavailable
Measuring completed
Invalid auto focus parameters
Homing failed, measuring not completed
Measuring failed, tool head unable to move
Auto focus timed out
Machine is not idle, this command cannot be executed
Measuring is in progress, please do not initiate again
Core controller offline, unable to measure
Measuring failed
Measuring failed to start
Target measuring position exceeded limit, measuring not completed
Measuring failed, command parsing exception
Measuring failed, core controller error
Cancelling in progress, please do not initiate again
Cancelling measuring failed
Z-axis return abnormal
Measuring actuator unavailable
WiFi scan failed
WiFi connected
WiFi connection failed
WiFi disconnect failed
IP acquisition or setup failed
Invalid Wi-Fi configuration parameters
Wireless network card not found
Interface is not WiFi type
WiFi password or authentication error
WiFi access point not found
WiFi association timeout
Wi-Fi connected, but IP acquisition failed
WiFi forget network failed
BLE scan failed
Bluetooth connected
Bluetooth connection failed
Bluetooth connection failed, parameter error
Bluetooth device removed
BLE manager not initialized
Purifier command failed
Purifier query failed
Invalid purifier parameters
Log export successful
Log export already running
Log source not found
No log files to export
Export directory creation failed
Log export failed, compression error
Log export failed, source file error
Log export failed, error writing compressed file
Log export failed, unknown error occurred while calculating checksum
Log export failed, unknown error
Log export failed, unknown error
Log export failed, unknown error
Log export failed, target directory space insufficient
Log export failed, unknown error
Machine motion calibration completed
Invalid command parameters
Machine is not idle, this command cannot be executed
Core controller offline, unable to execute calibration
Motion calibration already started, please do not initiate again
Failed to start machine motion calibration
Failed to stop motion calibration
Homing failed, device calibration not executed
Tool head unable to move, calibration failed
Machine motion calibration failed
Z-axis reset abnormal
Cover opened, motion calibration aborted
Cover opened, motion calibration aborted
Invalid parameters
Target disconnected
Invalid maintenance item
Unsupported maintenance action
Maintenance item disabled
Maintenance action failed
Camera calibration successful
Invalid camera calibration parameters
Camera calibration failed, parameter save not completed
Firmware upgrade failed
Firmware upgrade successful
Device is already executing the upgrade process, please do not initiate again
XYZ homing failed
Exhaust fan speed abnormal
Cooling fan not detected
Cooling fan speed abnormal
Measuring detection abnormal
Z-axis reset failed
Limit switch abnormal, please troubleshoot
Cover not closed, please close before continuing
Cover not closed, please close before continuing
First motion calibration failed
First motion calibration failed